Stainless Steel Bathroom Sink Floor Drain Stopper 1 1 2"

Kinds of Bathroom Sink Drain Stopper

There are several types of bathroom sink drain stoppers, and the most common ones include:

1. Pop-up Drain Stopper: This type of stopper is commonly found in modern bathroom sinks. It consists of a knob or lever behind the faucet that you can lift or push down to open or close the stopper. When you lift it, the stopper "pops up," allowing water to drain. When you press it down, the stopper seals the drain, preventing water from flowing out.

2. Lift-and-Turn Drain Stopper: This stopper requires you to manually lift it and then turn it to seal or unseal the drain. It operates similarly to a threaded screw: rotating it in one direction lifts the stopper, and rotating it in the opposite direction closes the drain.

3. Push-and-Pull Drain Stopper: The push-and-pull stopper is a simple design where you push it down to close the drain and pull it up to open it. It is a common type found in many older sinks.

4. Rubber Stopper or Plug: Some sinks may have a basic rubber stopper or plug that you manually place over the drain to block water. These are often used in utility sinks or older sink models.

5. Trip Lever Drain Stopper: This type of stopper is typically found in bathtub drains but can also be used in some bathroom sinks. It operates with a lever located on the overflow plate. When you flip the lever up or down, it controls the stopper's position, either sealing or opening the drain.

It's important to note that the specific type of drain stopper your sink has may vary depending on the sink's design and manufacturer. If you encounter any issues with the stopper not working correctly, it's worth inspecting it to see if there is any debris or hair trapped around the stopper assembly. Regular cleaning and maintenance can help keep your sink drain stopper functioning smoothly.

how to replace Bathroom Sink Drain Stopper

Replacing a bathroom sink drain stopper is generally a straightforward process, but the exact steps may vary slightly depending on the type of stopper you have. Below, I'll provide a general guide that should cover most types of bathroom sink drain stoppers:

Tools and Materials Needed:

• New bathroom sink drain stopper (make sure to get the right type that fits your sink)
• Adjustable pliers or pipe wrench
• Screwdriver (if applicable)
• Plumbers' putty or silicone sealant
• Towel or cloth

Step-by-Step Guide:

1. Clear the Area: Remove any items from the sink and clear the area so you have ample workspace.

2. Access the Drain Stopper Assembly: Underneath the sink, locate the drain pipe and find the rod connected to the drain stopper assembly. It might be a linkage rod, a horizontal rod, or a clevis strap, depending on the type of stopper.

3. Disconnect the Rod: If your sink has a pop-up drain stopper, you'll see a horizontal rod connected to the back of the drain tailpiece. Disconnect this rod by loosening the nut or clip that holds it in place. If you have a different type of stopper, such as a lift-and-turn or push-and-pull stopper, you may need to remove a pivot rod or other linkage that connects the stopper to the drain.

4. Remove the Old Stopper: With the rod disconnected, you should be able to lift the old stopper out of the drain. If it's held in place with any screws or brackets, remove those as well.

5. Clean the Area: Use a towel or cloth to clean any debris or old plumber's putty from around the drain opening.

6. Apply Plumbers' Putty: If your new stopper requires a watertight seal, apply a thin layer of plumbers' putty or silicone sealant around the underside of the flange of the new stopper.

7. Install the New Stopper: Insert the new stopper into the drain opening and press it firmly to create a seal with the putty or silicone.

8. Reconnect the Rod: If your new stopper has a mechanism that requires a linkage rod, reconnect the rod to the stopper assembly. Ensure that the stopper moves up and down smoothly when you operate the rod from above the sink.

9. Test the Stopper: Before finishing the installation, test the stopper by filling the sink with water and checking if it holds water when closed and drains properly when open.

10. Adjustments: If the stopper does not seal properly or is difficult to operate, you may need to make some adjustments to the linkage rod or other components.

11. Tighten Connections: Once you are satisfied with the stopper's performance, tighten any nuts or clips that hold the linkage rod or other parts in place.

Replacing a bathroom sink drain stopper is typically a DIY-friendly task, but if you encounter any complications or are unsure about any step, it's always best to consult a professional plumber for assistance.

Package Detail

OEM Logo Polybag, Colour Boxs, Colour Master Carton

• FAQ

Q: How long is your product guarantee period?
A: We have Two years guarantee and 24 hours full-time service.

Q: What is your MOQ?
A: Normal Each Items 3000pcs MOQ.

Q: Can you accept OEM,ODM?
A: we accpet OEM.

Q: How long is your delivery time?
A: 30-35 days After Confirm Order